Position the test light tool on the collar probes and look for the light to illuminate. The highest the correction level on the collar the brighter the light will shine. If the collar beeps or the test light tool illuminates, the battery and collar are working. If not, replace the battery.
Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been reset and will begin flashing as normal.
Insert the coin in the slot on top of the Power Cap unit and turn it 45 degrees counter-clockwise. Do not push down while turning. The Power Cap unit will rotate while the spring inside will push the Power Cap battery out of the Computer Collar unit battery chamber.
Make sure the collar is powered on. Press and hold the button on the collar until a beep is heard and the light flashes green to turn the collar on. Press and hold the power button for 10 seconds to reset the collar.
An Invisible Fence® Brand Power Cap Battery is the easiest way to ensure they stay safe. Even the best trained pets are susceptible to outside distractions, but a fresh Power Cap® Battery keeps them within their boundary.
All invisible fence systems have some type of indicator light on the transmitter that shows if the system is functioning and there is no break in the boundary wire. It may be a single light that goes out when the wire is broken; an alarm may also sound or there may be several lights that flash.
Saturation: Indicates Loop 1 transmitter output saturation. Loop saturation exists when the signal has reached maximum output level, which is caused by excessive loop size, excessive resistance, or poor connections.
How to Find Buried Invisible Fencing
- Make sure your invisible fence is plugged in and turned on. You should see an indicator light on the radio transmitter unit confirming this.
- Find the radio frequency that your invisible fence is using.
- Walk through your yard with the AM radio tuned to the correct radio frequency.
Invisible Fence compatible collar for fences running on the 10k frequency.
The procedures for measuring intentional radiators operating on frequencies below 30 MHz are given in 47 CFR 15.31(f). In the case of a dog fence transmitter or pet containment device operating at 10 kHz, a 40 dB per decade roll-off is acceptable.
They can be moved and adjusted more easily than a traditional fence. They allow dogs to roam the whole property. Dogs can't escape by digging under or jumping over them. They are generally effective at keeping dogs on the property.
If you have started to see a red flashing light on your pet's Computer Collar unit, your Power Cap battery may need to be replaced. If your Invisible Fence control panel is beeping with a lengthy pause between each beep, it's possible your backup battery unit needs to be replaced.
Since PetSafe Professional systems are professionally installed and can be set to custom frequencies, we would be unable to say for sure whether your transmitter is set to the standard PetSafe frequency of 10.65 kHz.
The receiver collar will emit a unique double tone as the contact points touch your pet's skin. You will know that you have the proper fit when you hear the receiver collar emit the double tone and it flashes green 5 consecutive times. 10. After 90 seconds, the receiver collar moves into normal operation mode.
We recommend changing the battery every 3 months - it's the safest, easiest and most reliable way to guarantee your pet's safety 100% of the time. To purchase a Power Cap battery or renew your Power Cap plan online, click here. Where can I buy batteries for my Invisible Fence collar?
Description: Invisible Fence® Brand Computer Collar® units are powered by a specially designed 3-Volt Lithium Power Cap® battery that Canine Company recommends replacing every 3 months to ensure continuous and trouble-free operation of your dog's Computer Collar. All batteries have a shelf life.
The collar will beep or blink in series to indicate the new shock level. Press the button again within 5 seconds to raise the level once more. Continue until the collar indicates it is at the correction level you desire. To lower the correction level, continue pressing the button; the level will cycle back to 1.
How to Change the Strength of an Invisible Fence
- Push the button on the receiver. A light on the receiver will flash.
- Adjust the distance from the boundary wire to trigger a warning alarm. Most transmitter boxes have a knob or lever to use to change the distance.
- Change the metal prongs on the receiver.
All Invisible Fence® Brand Computer Collars® require a specially designed 3-Volt Lithium Power Cap® battery. In order to continue to keep your dog confined within the safety of your yard, we recommend replacing your Computer Collar battery every 3 months.
